Log in
onclick="gourl('https://www.adsalecprj.com/en/auth/register.html')" v-if="!userInfo.id"> Register
Contact
{{userInfo.company_name_english||userInfo.truename_english}}
{{userInfo.phone||userInfo.email}}

Home Page

Member Center

Data Settings

Log out

 
Medical

ENGEL to present all-electric machine for the diagnostics market at K 2025

Sep 9, 2025

At K 2025, ENGEL will present an integrated, fully automated production solution for the diagnostics market, highlighting the premiere of a new validation assistant in the cell.

 

The system achieves an increase in overall efficiency of approximately 25 % compared to conventional production methods. In a single cell, well plates and lids are produced and packaged in a validated manner. At the heart of the solution is an all-electric ENGEL e-motion 280 WP combi MW injection molding machine with 2800 kN clamping force.


ENGEL_e-motion 280 combi MW.jpg


ENGEL e-motion 280 combi MW.

ENGEL_well plates with lids.jpg


Well plates with lids.

 

Two machines in one

 

ENGEL’s compact system concept combines with the innovative high-performance Variotwinstack mold technology from HACK Formenbau GmbH to implement the principle of two machines in one.

 

The mold is designed for the simultaneous production of up to four polystyrene well plates with 24 wells and their matching lids. For optimal media connection, the e-motion features a movable center platen. The two injection units operate in parallel, reducing the cycle time to just 11 seconds. The shot weight for the well plates is 42.6g, and 13.2g for the lids.

 

The angled arrangement of the moving injection unit brings the nozzle closer to the hot runner, reducing its volume and thus increasing process reliability. Valve gate hot runner injection without a sprue optimizes material usage while completely eliminating weld lines and flow marks. A multi-stage demolding process with intelligent cooling and optimal part orientation further provides a particularly wide process window.

 

In addition, integrated HACK moldlife sense sensor technology continuously monitors the mold mechanics, increases system availability and detects faults at an early stage. This system also supplies data to support digitally assisted process validation.

 

Premiere: New validation assistant in the cell

 

ENGEL will premier its new validation assistant in this cell – a system for digitally assisted qualification and validation of injection molding processes. Developed in collaboration with HACK Formenbau and Professor Thomas Seul, the solution combines ENGEL’s iQ assistance systems, moldlife sense technology and structured software modules.

 

It supports all validation phases from DQ to PQ, accommodates future release methods such as parametric release, and simplifies the transfer of validated processes to additional machines or sites. As a result, both time and staffing requirements for validation are significantly reduced, leading to a much shorter time to market.

 

Compact, precise and cleanroom-ready

 

One of the key advantages of this production solution lies in its reduced system height by the newly designed layout, with overall footprint of the production cell is reduced by 40%.

 

ENGEL’s e-motion series has been specifically developed to meet the most demanding requirements in injection molding for medical technology and sets new standards in precision, efficiency and long-term cleanroom performance.

 

Automated post-processing

 

After demolding, a side-entry robot from Ilsemann removes the molded parts. Two arms simultaneously grip the parts from both sides of the mold and transfer them either to a sampling station or to a laser marking station where a QR code is applied. The parts are then automatically assembled, stacked and sealed in sterile packaging.


Injection molding machines
Diagnostics equipment
K Fair
ENGEL
Comments
Automotive
Tederic is expanding its presence in Brazil’s automotive components market with its first NEO·M1920v three-color injection molding machine at a former Valeo automotive lighting plant.
Nov 3, 2026
Packaging
Husky Technologies announced capacity expansion at its Shanghai Manufacturing Center of Excellence and the global introduction of HyCAP PRO, its injection molding system for high-output beverage closure.
Oct 29, 2026
Automotive
Tederic delivered its first large-scale overseas project in the automotive lighting sector at the Thailand plant of Varroc, a leading Indian automotive components manufacturer.
Oct 28, 2026
Injection
At Fakuma 2026, Haitian will showcase two machines live – Haitian Jupiter two-platen series for automotive application and the 5th generation Zhafir Zeres F with caps & closures app.
Oct 8, 2026
Injection
At Fakuma 2026, ENGEL will demonstrate production of automotive connectors with the electric WINTEC e-win 1800 and the new viper 6.
Oct 6, 2026
Injection
At Fakuma 2026, ENGEL will demonstrate the series production of auto-injector components on the all-electric e-mac 200, which combines an exceptionally small footprint with high output.
Sep 24, 2026
Share Your Choice
Facebook
X
Email